Introduction This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). te 05 ibi 2- roh 1 ah 20 p ep d: king s e vy ad or Na nlo netw to ow d RI D n SI 647 ng a I / by /4 yi d 5/2 cop e ns :2 ly, ce R n Li BE e o M nc NUlice # r r de use Or leg n Si Representations of specifications in the form of a 3D model have been 2added.
DIN ISO 5459 PDF ISO
This third edition cancels and replaces the second edition (ISO 1101:2004) and ISO 10578:1992. ISO 1101 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. ISO shall not be held responsible for identifying any or all such patent rights. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. The main task of technical committees is to prepare International Standards. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. The work of preparing International Standards is normally carried out through ISO technical committees. 103įoreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). 99 Annex D (informative) Relation to the GPS matrix model.
95 Annex C (normative) Relations and dimensions of graphical symbols. 92 le ng SiĪnnex B (normative) Assessment of geometrical deviations. 35 lic r r de -use r A (informative) FormerOpractices. 33 ce R n Li BE e o M c n U e Definitions of geometrical# Ntolerances. 30 d /2 op se :25 y, c n l Orientation planes. 30 I IR 7D an IS /64 ing y b /4 y Intersection planes. 30 vy ad or Na nlo netw o ow d t Interrelationship of geometrical tolerances.
DIN ISO 5459 PDF FREE
27 h 01 proĪ 2 ep d: king s e Free state condition. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.
DIN ISO 5459 PDF PRO
2 ted 05 hibi 2 h 01 pro pa : 2 ng e d i s e k vy ad or Na nlo netw to ow d RI D n SI 647 ng a I / by /4 yi d 5/2 cop e ns :2 ly, ce R n Li BE e o M nc NUlice # r r de use Or leg n SiĬOPYRIGHT PROTECTED DOCUMENT © ISO 2012 All rights reserved.
2 ted 05 hibi 2 h 01 pro pa : 2 ng e d i s e k vy ad or Na nlo netw to ow d RI D n SI 647 ng a I / by /4 yi d 5/2 cop e ns :2 ly, ce R n Li BE e o M nc NUlice # r r de use Or leg n Siħ. Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out Spécification géométrique des produits (GPS) - Tolérancement géométrique - Tolérancement de forme, orientation, position et battement 7.
0 kommentar(er)
